Code compliant fasteners and structural fixing systems require a high degree of reliability, and any compromise on quality cannot be accepted. Every detail of an Erico CADDY fastener component, from initial conception through design and manufacture, is aimed towards providing cost effective solutions.
CADDY Fasteners offer:
Time and money savings
Simple and easy installation...
A hammer, pliers and screwdriver can be the only requirements. For certain applications manual installation is possible.
A complete range of products...
More than 5000 types of CADDY products, often offering several options for any one given application
Quality Control...
CADDY Fasteners, manufactured by ERICO, are produced from spring steel, galvanized steel, plastic, as well as other materials. Erico is know in the industry as a leader in the design and production of spring steel fasteners.
Load Rating...
CADDY Fasteners are designed with two load limits:
- Static load limit is a rated stationary load limit for a fastener. ERICO standards require that test samples withstand a load equal to 3x this rating.
- The ultimate static load limit is a rated stationary load limit which, if exceeded, may cause failure of the fastener. ERICO standards require that test samples withstand this rating. Some CADDY fasteners also are designed with an undefined rating and are to be used for positioning only with no loading on them.
Static load limit and ultimate static load limit values specify maximum allowable installed loads for user applications. These values are for loads applied VERTICALLY to the normal fastener installation except as may be diagrammed otherwise. Where the load rating of the CADDY fastener exceeds that of the structural member, the lowest rated item must set the load limit.
NOTE: CADDY fasteners are intended for support of electrical components at stationary loads. Not to be used for dynamic loads such as fluid and gas distribution components, etc.
Important...
CADDY fasteners used with wire, rod or threaded rod are designed for use with coarse round wire, hot rolled carbon steel bar, cold rolled carbon steel bar and threaded rod all meeting AISI specifications for tolerances.
Stud Wall
Mounting Plate Brackets (Non-Metallic)
|
Features:
No sharp metal edges with new plastic design
Fastest, easiest way to install
No installation tools required to secure bracket in the drywall opening
Serrated interlocking system secures tight
Template points on brackets eliminate multiple measurement markings during installation
Recessed design assures flush mount of device
Only CADDY provides the industry with the widest application range 1/4" to 1-1/4"
Available in single gang, double gang and a unique 3-4 gang size
Eliminates the need for electrical boxes on low voltage class 2 applications
NOTE: For low voltage Class 2 use only
|
Ordering Information |
---|
| Catalog Number | Description | QTY Per Box |
---|
| MP1P | Single gang mounting plate | 100 | | MPAL2 | Double gang mounting plate | 100 | | MP34P | 3 or 4 gang mounting plate | 20 |
Mounting Plate Brackets (Metallic)
|
Features:
Provides positive support with locking screws (included)
Mounts any standard low voltage device in 1/2" through 1-1/4" walls
Makes wire "fishing" easier
Install with a drywall saw and screwdriver
Eliminates the need for an electrical box when installing low voltage Class 2 wiring
NOTE: For low voltage Class 2 use only
|
Ordering Information |
---|
| Catalog Number | Description | QTY Per Box |
---|
| MPLS | Single gang screws to drywall (screws included) | 100 | | MPLS2 | Double gang screws to drywal (screw included) | 100 |
Low Voltage Mounting Brackets - For New Construction
|
Features:
Provides a bracket for mounting low voltage Class 2 communication outlets
Side support provides for a rigid installation
May be installed to the front or the side of the metal or wood stud
Eliminates bulges in the dry wall caused by plaster rings
Attaches with sel-tapping screws or nails
Works with 1/2" and 3/8" dry wall
Compliant with TIA/EIA-569-A (2/98) and TIA/EIA-570-A (10/99) standard
|
Ordering Information |
---|
| Catalog Number | Description | QTY Per Box |
---|
| MP1S | Plate mounting bracket for new work | 25 | | MP2S | Double gang plate mounting bracket for new work | 25 |
Box Mounting Brackets - For Between Studs
|
Features:
Supports electrical boxes, plaster rings or low voltage devices from one bracket
Accommodates up to four 4" or 4-11/16" boxes
Mounts 1-1/2" or 2-1/8" deep boxes
Eliminates the need for an electrical box on low voltage applications
Compliant with TIA/EIA-569-A (2/98) and TIA/EIA-570-A (10/99) standards
|
Ordering Information |
---|
| Catalog Number | Description | QTY Per Box |
---|
| RBS16 | Mounts up to three 4" or 4-11/16" boxes/plaster rings 16" bracket | 25 | | RBS24 | Mounts up to four 4" or 4-11/16" boxes/plaster rings 24" bracket | 25 |
Cabble Grippers
|
Features:
Installs easily to metal and wood studs
Provides secure installation of multiple cables with unique locking/unlocking system
Staples, nails or screws in metal studs without tools
Supports four NMC or eight 4 pair UTP cable (electrical and datacomm cannot be combined)
Delivers compliance with: NEC 300-4(d), CEC 12-510 and 12-516
|
Ordering Information |
---|
| Catalog Number | Description | QTY Per Box |
---|
| CG4 | Cable gripper cable support | 100 |
Metal Stud Punch and Easy Snap Grommet
|
Grommet Features:
Snap one grommet into standard 1-11/32" field punched hole, OR snap two together into any shape factory punched hole
Provides full 360 degree protection for cable and makes cable pull easier
Delivers compliance with: NEC Article 300-4(b)(1) and CEC Rule 12-516
Punch Features:
New cushioned handles mean less operator fatigue and more comfortable handling
New tool design with offset handles allows punch to work in confined locations and near perpendicular walls
Lightweight punch makes accurate location of holes easier
Hardened steel components keep tool sharper longer - less replacement
Punches up to 20 gauge sheet metal
Plastic grommets snap easily into 1-11/32" hole
|
Ordering Information |
---|
| Catalog Number | Desription | QTY Per Box |
---|
| MSP20 | Metal stud punch | 1 | | ESG1 | Easy snap grommet | 100/1000 |
Press-On Protection Plate - For Wood and Metal Studs
|
Features:
Fastest nail plate protection; no tools required
Protects electrical, Datacomm and plumbing
Works on wood or metal studs
16 GA. steel to meet NEC 300-4(b)(2)
Breakable tabs permit multiple plates to be ganged together
Corrosion resistant zinc phosphate coating
|
Ordering Information |
---|
| Catalog Number | Description | Material | TQY Per Box |
---|
| 304B2 | Press-on protection plate | 16 GA. steel with zinc phosphate | 100 |
Beam
Hammer-On Flange Clip
|
Features:
Locates a "portable" 1/4" hole with just a hammer
Installs easily regardless of insulation materials on beam flange
Fits most beams and bulb tees
|
Ordering Information |
---|
| Catalog Number | Flange Thickness | QTY Per Box | Static Load Limit |
---|
| 2H4 | 3/32" - 9/64" | 100 | 160 lbs. | | 4H24 | 1/8" - 1/4" | 100 | 200 lbs. | | 4H58 | 5/16" - 1/2" | 100 | 200 lbs. | | 4H912 | 9/16" - 3/4" | 100 | 200 lbs. |
Multi-Purpose Clip
|
Features:
Supports drive rings or bridle rings from flange
Accommodates any beam flange from 1/8" to 1/2" thickness
Accommodates standard 1/4"-20 or #10-24 threaded bridle rings, standard drive rings as well as unthreaded bridle rings
Requires only hammer to install
|
Ordering Information |
---|
| Catalog Number | Description |
---|
| 2FMP28 | Multi-purpose clip for drive rings and bridle rings |
Hammer-On Flange Clip
|
Features:
When used with CADDY combination conduit hanger, the conduit run lines up with "knock-outs" in outlet box and eliminates offsets and bends
Provides with a 1/4" - 20 thread impression so that the box may be quickly and securely attached to the clamp
Also available with a staked stud, 1/4" - 20 x 3/8" to provide easier attachment of outlet boxes to beams. Eliminates having to use loose screws
The CADDY combination washer-wing nut (Cat. No. 4WN) can be used to attach box (Not included)
|
Ordering Information |
---|
| Catalog Number | Flange Thickness | QTY Per Box |
---|
| M24 | 1/8" - 1/4" | 100 | | M58 | 5/16" - 1/2" | 100 | | M912 | 9/16" - 3/4" | 100 | | M24S | 1/8"-1/4" | 100 | | M58S | 5/16"- 1/2" | 100 | | M912S | 9/16" - 3/4" | 100 |
Flange Mount Conduit Clip - Snap Close
|
Features:
Available with CADDY CONDUIT CLIP bottom mounted or side mounted
Available for 3/8" through 2" EMT, rigid and aluminum conduit
Requires only hammer and pliers to install
Will pivot through 360 degrees
|
Ordering Information |
---|
| | Description | QTY Per Box | 6M24 | 6M24SM | 3/8" MC/AC cable to 1/8" to 1/4" flanges | 100 | 6M58 | 6M58SM | 3/8" MC/AC cable to 5/16" to 1/2" flanges | 100 | 6M912 | 6M912SM | 3/8" MC/AC cable to 9/16" to 3/4" flanges | 100 | 812M24 | 812M24SM | 1/2" to 3/4" conduit to 1/8" to 1/4" flanges
| 100 | 812M58 | 812M58SM | 1/2" to 3/4" conduit to 5/16" to 1/2" flanges
| 100 | 812M912 | 812M912SM | 1/2" to 3/4" conduit to 9/16" to 3/4" flanges
| 100 | 16M24 | 16M24SM | 1" conduit to 1/8" to 1/4" flanges
| 100 | 16M58 | 16M58SM | 1" conduit to 5/16" to 1/2" flanges
| 100 | 16M912 | 16M912SM | 1" conduit to 9/16" to 3/4" flanges
| 100 | 20M24 | 20M24SM | 1-1/4" conduit to 1/8" to 1/4" flanges
| 100 | 20M58 | 20M58SM | 1-1/4" conduit to 5/16" to 1/2" flanges
| 100 | 20M912 | 20M912SM | 1-1/4" conduit to 9/16" to 3/4" flanges
| 50 | 24M24 | 24M24SM | 1-1/2" conduit to 1/8" to 1/4" flanges
| 50 | 24M58 | 24M58SM | 1-1/2" conduit to 5/16" to 1/2" flanges
| 50 | 24M912 | 24M912SM | 1-1/2" conduit to 9/16" to 3/4" flanges
| 50 | 32M24 | 32M24SM | 2" conduit to 1/8" to 1/4" flanges | 50 | 32M58 | 32M58SM | 2" conduit to 5/16" to 1/2" flanges
| 50 | 32M912 | 32M912SM | 2" conduit to 9/16" to 3/4" flanges
| 50 |
Beam Clamps
|
Features:
Easy installation to beam flangs up to 1/2"
Supports 1/4" and 3/8" threaded rod, S-hooks, electrical boxes, conduit, J-hooks and bridle rings
Accommodates standard 1/4"-20 or #10-24 threaded bridle rings
NOTE: When using rigid conduit on P series, use next size larger clip (1/2" rigid use 12P)
|
Ordering Information |
---|
Catalog Number | Fig No. | Description | Static Load Limit | QTY Per Box |
---|
BC | 1 | Beam clamp thru 1/2" flange | 100 lbs. | 100 | BC812M | 2 | 1/2" to 3/4" conduit to beam thru 1/2" flange | 100 lbs. | 100 | BC16M | 2 | 1" conduit to beam thru 1/2" flange | 100 lbs. | 100 | BC20M | 2 | 1-1/4" conduit to beam thru 1/2" flange | 100 lbs. | 100 | BC24M | 2 | 1-1/2" conduit to beam thru 1/2" flange | 100 lbs. | 50 | BC32M | 2 | 2" conduit to beam thru 1/2" flange | 100 lbs. | 50 | BC812MSM | 3 | 1/2" to 3/4" conduit to beam thru 1/2" flange | 25 lbs. | 100 | BC16MSM | 3 | 1" conduit to beam thru 1/2" flange | 25 lbs. | 100 | BC20MSM | 3 | 1-1/4" conduit to beam thru 1/2" flange | 25 lbs. | 100 | BC24MSM | 3 | 1-1/2" conduit to beam thru 1/2" flange | 25 lbs. | 50 | BC32MSM | 3 | 2" conduit to beam thru 1/2" flange | 25 lbs. | 50 | BC8P | 4 | 1/2" conduit to beam thru 1/2" flange | 25 lbs. | 100 | BC12P | 4 | 3/4" conduit to beam thru 1/2" | 25 lbs. | 100 | BC16P | 4 | 1" conduit to beam thru 1/2" flange | 25 lbs. | 100 | BC8PSM | 5 | 1/2" conduit to beam thru 1/2" flange | 15 lbs. | 100 | BC12PSM | 5 | 3/4" conduit to beam thru 1/2" | 15 lbs. | 100 | BC16PSM | 5 | 1" conduit to beam thru 1/2" flange | 15 lbs. | 100 |
More Beam Clamps
|
Features:
Easy installation for beam flanges 1/8" to 5/8"
Supports 1/4" threaded rod, 1/4" threaded bridle rings and boxes
Available riveted to conduit clips 1/2" through 2"
Bright zinc finish
NOTE: See components section for threaded bridle rings
|
Ordering Information |
---|
| Catalog Number | Rigid | EMT | QTY Per Box |
---|
| BC200 | - | - | 50 | | BC200-CD0B | 1/2" | 1/2" | 50 | | BC200-CD1B | 3/4" | 3/4" | 50 | | BC200-CD2B | 1" | 1" | 50 | | BC200-CD2.5B | - | 1-1/4" | 50 | | BC200-CD3B | 1-1/4" | 1-1/2" | 50 | | BC200-CD4B | 1-1/2" | - | 25 | | BC200-CD5B | 2" | 2" | 25 |
Big Beam Clamps - Ideal for Electrical, Mechanical and HVAC Applications
|
Features:
Threaded holes accommodate 3/8" threaded rod or 3/8" bolt
Attaches to beam flange up to 3/4"
Ideal for creating a threaded rod trapeze
Bright zinc finish
|
Ordering Information |
---|
| Catalog Number | Description | QTY Per Box |
---|
| BC400 | For 3/8" threaded rod or 3/8" - 16 bolts to beam flange through 3/4" | 25 |
Reversible Beam Clamp with Side Mounting Threads
|
Features:
Easy installation to steel members up to 3/4" (20mm) thick
Reversible to allow installation to both top and bottom flange
Hardened cup point setscrew to provide secure grip on tapered sections
Threaded to quickly accommodate attachment of 1/4" dia. threaded rod, bridle rings and boxes from three positions - top, bottom and back
Heavy duty malleable iron construction with electrogalvanized finish for added corrosion protection
|
Ordering Information |
---|
| Catalog Number | Rod Size | Bolt Size | Flange Size Max | Coating | Qty Per Box | Top Load Limit | Bottom Load Limit |
---|
| BC260025EG | 1/4"-20 | 1/4"-20 | 3/4" | EG | 100 | 250 | 100 |
Cable Snap Clip
|
Features:
Supports cable from 1/16" - 1/2" flange
Works effectively with MC and AC cable dimensions 3/8" - 11/4" an low voltage cables from 7/32" and up
Clip "snaps" on flange and cable "snaps" into clip
|
Ordering Information |
---|
| Cable O.D. | Description | QTY Per Box | SC2A | .218-.281 | Low voltage, data and MC/AC cable to 1/16" thru 3/16" flange thickness | 100 | SC2B | .312-.375 | Low voltage, data and MC/AC cable to 1/16" thru 3/16" flange thickness | 100 | SC2C | .375-.437 | Low voltage, data and MC/AC cable to 1/16" thru 3/16" flange thickness | 100 | SC2D | .468-.562 | Low voltage, data and MC/AC cable to 1/16" thru 3/16" flange thickness | 100 | SC2E | .500-.718 | Low voltage, data and MC/AC cable to 1/16" thru 3/16" flange thickness | 100 | SC2F | .750-.937 | Low voltage, data and MC/AC cable to 1/16" thru 3/16" flange thickness | 100 | SC2G | .968-1.250 | Low voltage, data and MC/AC cable to 1/16" thru 3/16" flange thickness | 100 | SC4A | .218-.281 | Low voltage, data and MC/AC cable to 3/16" thru 9/32" flange thickness | 100 | SC4B | .312-.375 | Low voltage, data and MC/AC cable to 3/16" thru 9/32" flange thickness | 100 | SC4C | .375-.437 | Low voltage, data and MC/AC cable to 3/16" thru 9/32" flange thickness | 100 | SC4D | .468-.562 | Low voltage, data and MC/AC cable to 3/16" thru 9/32" flange thickness | 100 | SC4E | .500-.718 | Low voltage, data and MC/AC cable to 3/16" thru 9/32" flange thickness | 100 | SC4F | .750-.937 | Low voltage, data and MC/AC cable to 3/16" thru 9/32" flange thickness | 100 | SC4G | .968-1.250 | Low voltage, data and MC/AC cable to 3/16" thru 9/32" flange thickness | 100 | SC8A | .218-.281 | Low voltage, data and MC/AC cable to 5/16" thru 1/2" flange thickness | 100 | SC8B | .312-.375 | Low voltage, data and MC/AC cable to 5/16" thru 1/2" flange thickness | 100 | SC8C | .375-.437 | Low voltage, data and MC/AC cable to 5/16" thru 1/2" flange thickness | 100 | SC8D | .468-.562 | Low voltage, data and MC/AC cable to 5/16" thru 1/2" flange thickness | 100 | SC8E | .500-.718 | Low voltage, data and MC/AC cable to 5/16" thru 1/2" flange thickness | 100 | SC8F | .750-.937 | Low voltage, data and MC/AC cable to 5/16" thru 1/2" flange thickness | 100 | SC8G | .968-1.250 | Low voltage, data and MC/AC cable to 5/16" thru 1/2" flange thickness | 100 |
Rod/Wire Hanger
Hammer-On Plain and Threaded Rod Hangers - Beam Clamps
|
Features:
Used to suspend #8 wire, 1/4". 3/8" plain rod or 1/4" or 3/8" threaded rod from beam flanges 1/8" to 3/4" thick
Requires only a hammer to install
|
Ordering Information |
---|
Catalog Number | Fig No. | Flange Thickness | Rod Size | QTY Per Box |
---|
70824 | 1 | 1/8" - 1/4" | #8 wire or 1/4" plain rod | 100 | 70858 | 1 | 5/16" - 1/2" | #8 wire or 1/4" plain rod | 100 | 708912 | 1 | 9/16" - 3/4" | #8 wire or 1/4" plain rod | 100 | 6A24 | 2 | 1/8" - 1/4" | 3/8" (plain) | 100 | 6A58 | 2 | 5/16" - 1/2" | 3/8" (plain) | 100 | 6A912 | 2 | 9/16" - 3/4" | 3/8" (plain) | 100 | 4TI24 | 3 | 1/8" - 1/4" | 1/4" threaded | 100 | 4TI58 | 3 | 5/16" - 1/2" | 1/4" threaded | 100 | 4TI912 | 3 | 9/16" - 3/4" | 1/4" threaded | 100 | 4TI24 | 3 | 1/8" - 1/4" | 3/8" threaded | 100 | 4TI58 | 3 | 5/16" - 1/2" | 3/8" threaded | 100 | 4TI912 | 3 | 9/16" - 3/4" | 3/8" threaded | 100 | 6TA24 | 4 | 1/8" - 1/4" | 1/4" or 3/8" threaded (nuts required) | 100 | 6TA58 | 4 | 5/16" - 1/2" | 1/4" or 3/8" threaded (nuts required) | 100 | 6TA912 | 4 | 9/16" - 3/4" | 1/4" or 3/8" threaded (nuts required) | 100 |
Rod and Wire Hangers
|
Features:
ANGLE BRACKET suspends plain rod, threaded rod or wire drops from laminated wood or concrete beams, joists, ceilings and walls
OFFSET BRACKET suspends plain rod, threaded rod or wire drops from laminated wood or concrete beams, joists, ceilings and walls
NOTE: Loads indicated are for CADDY fasteners only. Method of attachment to structure must be evaluated separately
|
Ordering Information |
---|
Angle Bracket
Cat. No. | Fig. No. | QTY Per Box | Description | Offset Bracket
Cat. No. | Fig. No. | QTY Per Box |
---|
708AB | 1 | 100 | For #8 wire or 1/4" plain rod | 708AO | 5 | 100 | 6AB | 2 | 100 | For 3/8" plain rod | 6AO | 6 | 100 | 4TIB | 3 | 100 | For 1/4" threaded rod, with thread impression | 4TIO | 7 | 100 | 6TIB | 3 | 100 | For 3/8" threaded rod, with thread impression | 6TIO | 7 | 100 | 6TB | 4 | 100 | For 1/4" or 3/8" threaded rod, nuts required | 6TO | 8 | 100 |
Pin Driven Angle Brackets
Features:
Longer leg angle bracket for tool clearance
Designed to fit a variety of pin drivers
Improved for easier installation with pin drivers
Star hole provides more gripping power to align brackets
Pregalvanized steel
Preassembly options available for Rod, Wire, Strap and Cable Applications
NOTE: Load limits apply to CADDY fasteners only. Pin must be evaluated separately
Ordering Information |
---|
| Catalog Number | Description | Load | QTY Per Box |
---|
| CAT21AFAB3 | Cable support hanger with angle bracket - 1-5/16" diameter loop | 50 | 50 | | CAT32AFAB | Cable support hanger with angle bracket - 2" diameter loop | 50 | 50 | | CAT12AFAB3 | Cable support hanger with angle bracket, holds up to 16 cables of 4 twisted pair or fiber optic | 50 | 50 | | 6AFAB3 | For 3/8" plain rod | 160 | 100 |
Purlin
"C" and "Z" Purlin Clips
|
Features:
One fastener fits flanges 1/16" to 1/4"
Supports ire or rod from bar joist, C Purlin (VF14) or Z Purlin (AF14)
Installs from floor with VAFT tool and conduit
NOTE: VF for vertical flange only and AF for anlge flange only
|
Ordering Information |
---|
| Catalog Number | Description | QTY Per Box |
---|
| VF14 | 1/16" to 1/4" vertical flange for wrap wire, "S" hooks, bolting straps, WMX6 | 100 | | VF14708 | 1/16" to 1/4" to #8 wire or 1/4" plain rod | 100 | | VF146A | 1/16" to 1/4" to 3/8" plain rod | 100 | | VF144TI | 1/16" to 1/4" to 1/4" threaded rod | 100 | | VF146TI | 1/16" to 1/4" to 3/8" threaded rod | 100 | | VF146T | 1/16" to 1/4" to 3/8" threaded rod (nuts required) | 100 | | AF14 | 1/16" to 1/4" Z Purlin for wrap wire, "S" hooks, bolting straps, WMX6 | 100 | | AF14708 | 1/16" to 1/4" to #8 wire or 1/4" plain rod | 100 | | AF146A | 1/16" to 1/4" to 3/8" plain rod | 100 | | AF144TI | 1/16" to 1/4" to 1/4" threaded rod | 100 | | AF146TI | 1/16" to 1/4" to 3/8" threaded rod | 100 | | AF146T | 1/16" to 1/4" to 3/8" threaded rod (nuts required) | 100 | - | VAFT | Installation tool for VF & AF assemblies | 1 |
Multi-Flange Rod Hanger
|
Features:
C or Z purlins pr up to 1/4" (7mm) horrizontal beam flange
Slotted, Hex, Robertson, Phillips combo head bolt
Hardened cup point setscrew for secure grip
Fast installation of threaded components; (1/4" or 3/8") No nuts required
Swivel feature option
Electrogalvanized finish for good corrosion protection
Available in hot dipped galvanized finish (special order)
NOTE: Loads up to 200 lbs. (0.90 kN) on C or Z purlins or 160 lbs. (0.71 kN) on horizontal beams
|
Ordering Information |
---|
| Catalog Number | Description | Thread | QTY Per Box |
---|
| PH4 | Rod hanger | 1/4" - 20 | 25 | | PH6 | Rod hanger | 3/8" - 16 | 25 | | PHSW4 | Rod hanger with swivel | 1/4" - 20 | 25 | | PHSW6 | Rod hanger with swivel | 3/8" - 16 | 25 |
Drop Wire/Rod
Cable/Conduit From Drop Wire Support
|
Features:
Supports cable and conduit without bending drop wire
Delivers 25% faster installation
Eliminates the need to trap cable/conduit against drop wire
|
Ordering Information |
---|
| Catalog Number | Description | QTY Per Box |
---|
| PCS1 | Flexible cable support from #8-#12 drop wire for MC/AC 14-2 through 12-3 with ground up to .600 O.D. | 100 | | PCS2 | Conduit/cable support from #8-#12 drop wire for 1/2" and 3/4" EMT, MC/AC up to .900 O.D. | 100 |
Multi-Function Clip - From Drop wire or Flange
|
Features:
Attaches to #12 wire thru 3/8" rod
Fits 1/8" to 3/8" flanges
Provides attachment of conduit and boxes
Supports #10-24 and 1/4" - 20 threaded bridle rings
|
Ordering Information |
---|
Catalog Number | Fig. No. | Description | Wire Size | Flange Size | QTY Per Box |
---|
4Z34 | 1 | Multi-function clip | #12 wire thru 1/4" plain rod | 1/8" - 3/8" | 100 | 4Z34812M | 2 | Multi-plus 1/2" or 3/4" conduit | #12 wire thru 1/4" plain rod | 1/8" - 3/8" | 100 | 4Z3416M | 2 | Multi-plus 1" conduit | #12 wire thru 1/4" plain rod | 1/8" - 3/8" | 100 | 4Z348P | 3 | Multi-plus 1/2" EMT conduit | #12 wire thru 1/4" plain rod | 1/8" - 3/8" | 100 | 4Z3412P | 3 | Multi-plus 3/4" EMT conduit | #12 wire thru 1/4" plain rod | 1/8" - 3/8" | 100 | 4Z3416P | 3 | Multi-plus 1" EMT conduit | #12 wire thru 1/4" plain rod | 1/8" - 3/8" | 100 | 6Z34 | 1 | Multi-function clip | 3/8" plain or threaded rod | 3/8" - 7/16" | 100 | 6Z34812M | 2 | Multi-plus 1/2" or 3/4" conduit | 3/8" plain or threaded rod | 3/8" - 7/16" | 100 | 6Z3416M | 2 | Multi-plus 1" conduit | 3/8" plain or threaded rod | 3/8" - 7/16" | 100 | 6Z348P | 3 | Multi-plus 1/2" EMT conduit | 3/8" plain or threaded rod | 3/8" - 7/16" | 100 | 6Z3412P | 3 | Multi-plus 3/4" EMT conduit | 3/8" plain or threaded rod | 3/8" - 7/16" | 100 | 6Z3416P | 3 | Multi-plus 1" EMT conduit | 3/8" plain or threaded rod | 3/8" - 7/16" | 100 |
Acoustical Tee
Independent Electrical Drop Wire/Rod Securing Clip
|
Features:
Prevents sway of dedicated electrical drop wire/rod
Doesn't negatively affect ceiling grid systems
No tools required, Forgiving desing doesn't require exact cutting of rod/wire
Painted yellow for yeasy identification by the inspector
NOTE: Consult local authority for application approval
|
Ordering Information |
---|
| Catalog Number | Description | QTY Per Box |
---|
| EC311 | Electrical drop wire securing clip #12 thru #8 wire | 100 | | EC3114Z34 | #12 wire thru 1/4" threaded rod | 100 | | EC3116Z34 | 3/8" threaded rod | 100 |
Narrow Base Cable Support
Plain, Threaded and Wood Screw Bridle Rings
|
Features:
When combined with other CADDY fasteners, bridle rings can be located on:
- Beam flanges up to 3/4" - 2FMP28, BC, BC200, M912
- Drop wire - 4Z34 - 6Z34
- Concrete - 4TIB
- "C" Purlins - VF144TI
- "Z" Purlins - 1224TI or AF144TI
- Acoustical T-Grid - ATS41 or ATA41
|
Ordering Information |
---|
| Catalog Number | "A" Dim. | Stock Dia. | QTY Per Box |
---|
| 2BR8 | 1/2" | #8 wire (.162) | 100 | | 2BR12 | 3/4" | #8 wire (.162) | 100 | | 2BR20 | 1-1/4" | #8 wire (.162) | 100 | | 2BR32 | 2" | #8 wire (.162) | 100 | | 2BRT8 | 1/2" | 10-24 threaded | 100 | | 2BRT12 | 3/4" | 10-24 threaded | 100 | | 2BRT20 | 1-1/4" | 10-24 threaded | 100 | | 2BRT32 | 2" | 10-24 threaded | 100 | | 4BRT20 | 1-1/4" | 1/4" - 20 threaded | 100 | | 4BRT32 | 2" | 1/4" - 20 threaded | 100 | | 4BRT64 | 4" | 1/4" - 20 threaded | 50 | | 4BRT20WS | 1-1/4" | #14 wood screw thread | 100 | | 4BRT32WS | 2" | #14 wood screw thread | 100 |
Flexible Conduit and Cable Hanger
|
Features:
Bundle runs of MC or AC or communications cables
Can be used with all flange clips or deck clip DH2. Also AO or AB, VF14, AF14, 122-123
Refer to local authorities and NEC Article 310 for derating ampacity when flexible power cables are used
|
Ordering Information |
---|
| Catalog Number | Number of Runs of MC/AC Cable That May be Supported | "A" Dim. | Ultimate Static Load Rating | QTY Per Box |
---|
| WMX3 | 3 | 1-1/8" | 50# | 100 | | WMX6 | 6 | 1-3/4" | 75# | 100 |
Strut
One-Piece Strut Clamp - SCH Series
|
Features:
One-piece installation means no screws or bolts to drop
Installs quickly and easily. Requires only a screwdriver or nut driver for installation
Heavy-duty construction with a bright zinc finish
Size 3/8" MC/AC to 4" EMT conduits
All sizes available with load distribution plate attached to screw
|
Ordering Information |
---|
| Catalog Number | EMT | Rigid | Cable O.D. Range | Static Load Limit | QTY Per Box |
---|
| SCH8 | 1/2" | - | - | 200 | 100 | | SCH12 | 3/4" | 1/2" | - | 200 | 100 | | SCH16 | 1" | 3/4" | - | v | 100 | | SCH20 | 1-1/4" | 1" | - | 200 | 100 | | SCH6B | 3/8" MC/AC | - | .10" - .63" | 200 | 100 | | SCH8B | 1/2" | - | .34" - .71" | 200 | 100 | | SCH12B | 3/4" | 1/2" | .57" - .92" | 200 | 100 | | SCH16B | 1" | 3/4" | .72" - 1.16" | 200 | 100 | | SCH20B | 1-1/4" | 1" | 1.00" - 1.51" | 200 | 100 | | SCH24B | 1-1/2" | 1-1/4" | 1.25" - 1.74" | 350 | 50 | | SCH32B | 2" | 1-1/2" | 1.74" - 2.20" | 350 | 50 | | SCH40B | - | 2" | 2.00" - 2.38" | 350 | 25 | | SCH48B | 2-1/2" | 2-1/2" | 2.38" - 2.88" | 350 | 25 | | SCH56B | 3" | 3" | 2.72" - 3.50" | 350 | 25 | | SCH64B | 3-1/2" | 3-1/2" | 3.25" - 4.00" | 350 | 10 | | SCH72B | 4" | 4" | 3.85" - 4.50" | 350 | 10 |
Break-Apart One-Piece Strut Clamp - SK Series
|
Features:
One-piece construction
Retained bolt and built-in nut eleminates dropping of loose parts
One size fits EMT and Rigid
Installs with screwdriver, standard wrench or nut driver
Break in half and install
Works with most struts
Bright zinc finish
|
Ordering Information |
---|
| Mild Steel | Stainless Steel | Aluminum | EMT Rigid | Mild & Stainless Steel Static Load | Aluminum Static Load | QTY Per Box |
---|
| SK85I | SK8SS | SK8ALA | 1/2" | 200 | 150 | 100 | | SK125I | SK12SS | SK12ALA | 3/4" | 200 | 150 | 100 | | SK165I | SK16SS | SK16ALA | 1" | 200 | 150 | 100 | | SK205I | SK20SS | SK20ALA | 1-1/4" | 200 | 150 | 100 | | SK245I | SK24SS | SK24ALA | 1-1/2" | 200 | 150 | 50 | | SK325I | SK32SS | SK32ALA | 2" | 200 | 150 | 50 | | SK405I | SK40SS | SK40ALA | 2-1/2" | 350 | 200 | 50 | | SK485I | SK48SS | SK48ALA | 3" | 350 | 200 | 50 | | SK565I | SK56SS | SK56ALA | 3-1/2" | 350 | 200 | 25 | | SK645I | SK64SS | SK64SS | 4" | 350 | 200 | 25 |
MC/AC
Snap-In Support
|
Features:
Manufactured with stabilizer legs for "wobble-free" support
One fastener for cable size 14-4, 12-4, 12-3, 12-2, 10-3, 10-2
Snaps into place on metal stud and beam flange up to 1/8" thick, no tools required for installation
MAC2 snaps in half to accommodate a single run of cable effectively making two clips from one
Prepunched holes in clip allow it to be screwed to wood stud, concrete or block
Factory riveted assemblies are available for installation on flange, purlin, acoustical tee, drop wire, concrete, black or wood and metal stud
Delivers compliance for: NEC Article 300-4(d) allowing cable to be positioned a minimum of 1-1/4" from face of stud. CEC Rule 12-618 for support of MC/AC cable
|
Ordering Information |
---|
Catalog Number | Fig. No. | Description | QTY Per Box |
---|
MAC2T | 2 | Support 1 to 4 runs of MC/AC cable for metal stud | 100 | MAC2 | 1 | Metal or wood stud and 1/8" flange | 100 | MAC2ATA | 3 | Acoustical Tee | 100 | MAC2BC | 4 | 1/8" thru 1/2" flange | 100 | MAC224SM | 5 | 1/8" thru 1/4" flange | 100 | MAC258SM | 5 | 5/2" thru 1/2" flange | 100 | MAC2912SM | 5 | 1/16" thru 3/4" flange | 100 | MAC2VF14 | 6 | 1/16" thru 1/4" C purlin or vertical flange | 100 | MAC2123 | 7 | Z purlin | 100 | MAC2AO | 8 | offset bracket | 100 | MAC224 | 9 | 1/8" thru 1/4" flange - bottom mount rotates 360 degrees | 100 | MAC258 | 9 | 5/16" thru 1/2" flange - bottom mount rotates 360 degrees | 100 | MAC2912 | 9 | 1/2" thru 3/4" flange - bottom mount rotates 360 degrees | 100 | MAC24Z34 | 10 | #12 thru 1/4" wire, plain or threaded rod & 1/8" thru 3/8" flange | 100 | MAC26Z34 | 10 | 3/8" plain of threaded rod and 3/8" thru 9/16" flange | 100 | MAC2FB | 11 | Through metal stud | 100 |
|